Design and Implementation of Torque Control and Estimation for an Electric Hand-Tool
Abstract
This paper proposes the design and implementation of torque control and torque estimation for an electric hand-tool. This hand-tool does not require any torque transducer or any Hall-effect sensor. Only some low-cost resistances are used to measure the stator currents of a brushless DC motor, which is used to drive the hand-tool. Novel 3-phase current commands are proposed here to obtain greater torque than traditional 3-phase, square-wave current commands. The output torque of the hand-tool can be estimated and displayed by an LED display. A PI controller is used to achieve the current-loop control. A digital signal processor, TMS-320-F2808 that was manufactured by Texas Instruments, is used to execute the control and estimation algorithms. Experimental results show the correctness and feasibility of the proposed methods.
Keywords
Full Text:
PDFReferences
Huang SJ, Huang KC, Huang TC, et al. Design of hybrid power supply system with energy regulation capability for hand-held tools. IEEE Trans. Ind. Electron. 2017; 64(2): 1148-1156.
Hesmondhalgh DE, Wain EA. Low-speed motorized dental handpiece. IEE Electric Power Appl. 1978; 1(3): 65-71. doi: 10.1049/ij-epa.1978.0012.
Hesmondhalgh DE, Tipping D, Amrani M. Design and construction of a high-speed high-performance direct-drive handpiece. IEE Proceedings1987; 134(6): 286-296. doi: 10.1049/ip-b:19870046.
Mecrow BC, Jack AG, Atkinson DJ, et al. High torque machines for power hand tool applications. IEEE PEMD 2002; 644-649. doi: 10.1049/cp:20020192.
Koinuma K, Aiso K, Akatsu K. A novel self cooling SRM for electric hand-tools. IEEE ECCE 2018; 6116-6120. doi: 10.1109/ECCE.2018.8557901.
Sathyan A, Milivojevic N, Lee YJ, et al. An FPGA-based novel digital PWM control scheme for BLDC motor drives. IEEE Trans. Ind. Electron. 2009; 56(8): 3040-3049. doi: 10.1109/tie.2009.2022067.
Shanmugasundram R, Zakariah KM, Yadaiah N. Implementation and performance analysis of digital controllers for brushless DC motor drives. IEEE/ASME Trans. on Mechatron. 2014; 19(1): 231-224. doi: 10.1109/TMECH.2012.2226469.
Han Q, Samoylenko N, Jatskevich J. Comparison of brushless DC motor drives with 180/120-degree inverter systems. IEEE CCECE 2007; 111-114. doi: 10.1109/CCECE.2007.35.
Krishnan R. Electric motor drives: Modeling, analysis, and control. London, UK: Prentice Hall; 2001.
Miller TJE. Brushless permanent-magnet and reluctance motor drives. Oxford, UK: Clarendon Press; 1989. doi: 10.1049/pe:19900006.
Kenjo T, Nagamori S. Permanent-magnet and brushless DC motors. Oxford, UK: Clarendon Press; 1985.
Krishnan R. Permanent magnet synchronous and brushless DC motor drives. NW, USA: CRC Press; 2010.
Bose BK. Modern power electronics and AC drives. NJ, USA: Prentice Hall; 2001.
Texas Instruments. TMS320x280xDigital Signal Processors; 2002.
Texas Instruments. TMS320x280X DSP Analog to Digital Converter; 2004.
Texas Instruments. TMS320x280x Enhanced Controller Area Network; 2002.
DOI: https://doi.org/10.18282/fme.v2i2.801
Refbacks
- There are currently no refbacks.